Cards- Shaker

A Mickey Shaker Card

Good morning.  I have a friend who sells Disney cruises.  She likes to send a thank you card to her customers.  Over the years, I have made her many types of cards.  I had a post on this a while back here.  Check it out.  Today, I have a new one for  her.

MM 2

It's a shaker card.  I thought it turned out well.  I started with a card base of Basic Black card stock.  It is cut 5 1/2 x 8 1/2, scored at 4 1/4 and folded.  This makes the regular A2 envelope size card.  I cut a layer of Real Red at 4 x 5 1/4.

MM 8

Use the Layering Circles Framelits to cut out the mouse shape.  You will have to run this through the Big Shot 3 times starting with the largest circles and then cutting each ear.  Run it through the Big Shot one more time using the Large Polka Dot embossing folder.  Dots are big in the Mickey world.  I cut a 3 1/2 inch square from a Window Sheet and glued it on the back of my layer.  Use your glue sparingly, but with good coverage.

MM 7

Have you tried the new Foam Adhesive Strips?  They are fantastic!  You'll need to put a layer of this strip all around the opening you made.  Make sure that you do not leave any open areas.  It's OK to piece this together as long as you leave no open spaces. The sides of this tape are sticky.  Take your Embossing Buddy and rub it around the inner sides of the foam tape to cut down on the stickiness.

MM 6

Put some of the Metallics Sequins Assortment packs.  Put about a teaspoon or so. They need room to shake.

MM 5

Carefully pull off the paper from the tape and adhere a piece of 3 1/2 inch square Basic Black card stock.

MM 4

Add some Fast Fuse to the back of the black card stock.  I also added some of the Foam Adhesive Strip along the top and the bottom.  Adhere to the front of the card.

On the front of the card, I added some Thick Whisper White 1/2 inch circle punch circles.  We are all about the dots!  The Thanks is also from the Thick Whisper White.  I used the Hello You Framelits.  Use the Fine-Tip Glue Pen to adhere.

MM 1

What a fun card!  I think my friend's customers will love getting their thank you card.  My supply list follows.  Need a demonstrator.  I can do that for you.  Just let me know if you need something!

Product List

Golden Jar of Love Shaker Card

I love shaker cards.  Stampin' Up!'s new Foam Adhesive Strips make it so easy.  But I'm getting a little ahead of myself.  Here's the card for today.

Jar shaker card

This shaker has a bit of sparkle.  We all know someone who loves the glitter and glam. This card is for them!  Lori, are you reading this!  Here are the details on how to make this card.  Warning, there are quite a few steps!

  • Start with a card base of Basic Black measuring 5 1/2 x 8 1/2, scored at 4 1/4 and folded.
  • Add of layer from the Gold Foil Sheets measuing 4 x 5 1/4.  When I see someone use so much of the gold foil sheets, I immediately think about the cost of those sheets.  Here's a tip I have to save a little.  Use your Stampin' Trimmer to cut out the inside of the piece you are using.  You can use the center for another project.

Jar shaker layer of gold

  • Now you have a layer of Basic Black measuring 3 1/2 x 4 3/4.
  • Finally, you have a layer of the gold dots paper from the Pop of Pink Specialty Designer Series Paper.  The measures 3 3/8 x 4 5/8.
  • Using the Everyday Jar Framelits, cut the largest jar from the confetti gold piece of designer paper from the Pop of Pink Specialty DSP.
  • Also cut this jar from a Window Sheet.
  • Now stamp the jar using the Jar of Love stamp set.  Stamp with Basic Black Archival ink onto Whisper White card stock.  Cut the outside and the inside of the stamped image using the Everyday Jar Framelits.
  • Adhere the Foam Adhesive Strips around the outside of the confetti piece as close to the edge as possible.
  • Add in your confetti from the Metallics Sequin Assortment.
  • Take off the top of the adhesive strips and adhere the top of the jar to the bottom.  Be very careful as you place the two together so you can match them properly.
  • Adhere the jar to your card front.  I suggest you use Fast Fuse or the Tear & Tape adhesive.
  • Stamp the lid with Basic Black Archival ink onto a piece of gold foil scrap.  Cut this out with the framelits.  I suggest that you let it dry just a little first.  Adhere to the top of your jar.

Jar shaker close up of tag

  • For the tag, I used the "You" from the Hello You Thinlits.  I cut it from Basic Black card stock and then colored it with the Wink of Stella.  It needed its own bit of glam.
  • The sentiment if from the Jar of Love stamp set.
  • Glue the "You" on just above the saying.  Use your Fine-Tip Glue Pen for this.
  • I used the Lots of Labels Framelit set to cut out the tag.
  • Add a few sequins.  I choose black ones.
  • Add a bow using the Black Solid Baker's Twine.
  • I used the new Black Metallic Thread behind the tag to add a little more interest.
  • Use dimensionals on the back of the tag.

Jar shaker inside

The sentiment on the inside of the card is from Gift of Love.  It's a Host set.  I added some sequins around the words.

 

Product List